Fill Dirt in Webb County, TX

Delivered fill-dirt in Webb County commonly falls in a wide range depending on source, quality, and haul distance; a typical ballpark is about $12 to $35 per ton (roughly $9 to $26 per cubic yard). Prices vary with moisture content, contaminants, and whether delivery or spreading is included, so use Hello Gravel to get exact local quotes for your zip code.

Hello Gravel connects you with local Webb County suppliers and haulers so you can see exact supplier options for your zip code. Standard delivery lead time is usually 2+ business days with next-day available for orders placed before noon CST; delivery fees vary by supplier and distance, minimum orders are commonly 3 tons, and some areas offer free delivery—confirm fees in checkout.

Ask for a well-graded fill-dirt with low organic content and a mix of sand, silt, and fines rather than loose topsoil or large debris; this gives better compaction and stability in Webb County's clay-prone soils. Avoid material with high organic matter or large roots, and if drainage is a concern ask for a sandier or crushed-rock blended option to reduce shrink-swell.

For simple yard grade raises, 2 to 6 inches of compacted fill-dirt is common, added in 6-8 inch loose lifts with compaction between lifts; larger grade changes require staged fills and an engineered plan. For driveways, fill-dirt alone is not a recommended surface—use fill-dirt only to raise grade under a structural base, then place a 4-6 inch compacted crushed stone or base material for the driveway surface.

Compact fill-dirt in 6-8 inch loose lifts to about 90-95% of Standard Proctor density for most landscaping and non-structural uses; small jobs can use plate compactors while larger jobs typically need sheepsfoot or vibratory rollers. Many homeowners hire local contractors who provide delivery, spreading, and compaction as bundled services—ask for written compaction specs and equipment details before work begins.

Webb County's hot summers and clay-rich native soils increase shrink-swell and slow infiltration, so untreated clay-heavy fill-dirt can crack when dry and pond after heavy rains. Improve performance by using well-graded or sand-amended fill, installing positive slopes and perimeter drainage, and avoiding placing uncompacted fills next to foundations or slabs without an engineered design.

You should check Webb County permitting and any HOA rules before changing grades or replacing turf with fill-dirt; permits may be required for driveway alterations, grading near easements, or work inside regulated floodplain areas. Also call 811 to locate buried utilities before digging and confirm local setback and drainage rules to avoid violations.

Calculate volume by multiplying area (sq ft) by desired depth (ft) to get cubic feet, then divide by 27 to convert to cubic yards; multiply cubic yards by about 1.2 tons per cubic yard for a practical ton estimate for typical fill-dirt. Example: raising 1,000 sq ft by 3 inches (0.25 ft) is 1,000 x 0.25 = 250 cu ft = 9.26 cu yd, roughly 11 tons using 1.2 tons/yd3—always round up for settlement and waste.

Use fill-dirt primarily for raising grade, backfill, and non-structural fills where compaction and stability are the main needs, but not as a finished driving surface. Choose crushed limestone or similar crushed-stone base for driveways and structural bases because they provide better drainage and load-bearing capacity, and pick decomposed granite for low-traffic paths and decorative surfaces where a compacted, natural look is desired.

Well-compacted, properly drained fill-dirt can perform for many years as yard fill or backfill, but expect some settlement over the first 1-3 years and occasional maintenance for erosion control after heavy rains. For areas with vehicle traffic, top with a structural base and surface material; for landscaping, finish with topsoil and vegetation to reduce erosion and the need for periodic regrading.

Contractors typically price projects using a combination of per-ton or per-yard material charges plus separate delivery, spreading, and compaction fees, or they may quote a flat job price that includes labor and equipment. When getting estimates ask for units (tons or cubic yards), lift thickness and compaction targets, whether hauling and spreading are included, and a written timeline so you can compare bids accurately.