Fill Dirt in Seal Beach, CA

A tri-axle dump truck typically carries about 10 to 12 cubic yards of loose fill dirt. Delivered price for a full truck to Seal Beach commonly falls in the range of $300 to $700, depending on material quality, haul distance, moisture content, and whether site access or permits add time. Exact pricing appears at checkout when we match you with local suppliers.

Cost depends on depth and whether you need spreading and compaction. For example, at 4 inches deep you need about 12.4 cubic yards; material delivered usually runs roughly $20 to $45 per cubic yard, so materials may be $250 to $560, and professional spreading/compaction can add $400 to $1,200, for a typical installed range of about $650 to $1,760. Prices vary by supplier, site conditions, and any required erosion control.

Assuming a 20‑ft long by 10‑ft wide driveway at 4 inches deep (about 2.5 cubic yards), delivered material alone is often $50 to $120, while labor for grading and compaction can range $200 to $900 depending on access and slope. Total job cost commonly runs $250 to $1,200 for a small residential driveway; steeper sites, removal of organics, or permitting raise the price.

Fill dirt is generally cheaper per cubic yard than quarried gravel, so material cost to raise grade is usually lower with fill dirt. However, for a finished driveway surface gravel is the more appropriate material and may save money long term because it provides drainage and a stable wearing surface; alternative stabilization or surfacing will add cost if you try to use raw fill dirt as a top layer.

You can place fill over existing soil, but best practice is to remove organic topsoil and place fill in loose lifts with compaction between layers to avoid future settlement. Professional grading and compaction for small jobs typically runs a few hundred to a few thousand dollars depending on area and access; expect modest jobs to cost $300 to $1,500 for labor in the Seal Beach area, with larger or complex sites higher.

Because Seal Beach is coastal and can have heavy rain events and sandy slopes, loose fill dirt is vulnerable to erosion if not compacted or stabilized. We recommend compaction and simple erosion controls (silt fence, tackifier, temporary mulch) for sloped or exposed areas; budget at least a few hundred dollars for basic erosion control on small projects, more for permanent measures like retaining walls or drainage improvements.

Common options include geotextile fabric, geogrids, polymer soil stabilizers, and cement or lime stabilization. Costs vary widely: geotextile or geogrid materials often run roughly $0.20 to $2.00 per square foot installed, polymer stabilizers around $0.50 to $3.00 per square foot, and cement/lime stabilization is usually $1.00 to $4.00 per square foot plus equipment; final choice depends on load requirements and local soil conditions.

Chip seal and asphalt sealcoats are surfacing treatments applied to pavement or compacted base and typically cost more per square foot than simple regrading with fill dirt; chip seal commonly runs about $1.50 to $3.50 per square foot for small residential areas. Regrading with fill dirt to adjust grade is generally less expensive per square foot for just material and labor, but it does not provide a wear surface—if you want a durable, low‑maintenance driveway you should budget for both proper base preparation and a final surfacing layer.

Delivered fill dirt in West California around the Seal Beach area commonly ranges from about $20 to $45 per cubic yard, depending on supplier, moisture content, and distance. Hello Gravel's minimum order is 3 tons (roughly 2 to 3 cubic yards depending on material density), but local suppliers may set their own minimums; checkout pricing shows exact local rates and minimums for your zip code.

Hello Gravel can supply and deliver fill dirt to Seal Beach through our network of local suppliers and contracted truckers. Drivers may be able to perform tailgate spreading at their discretion if you request it at checkout, but compaction usually requires a separate contractor; standard lead time is 2+ business days with a next‑day option for orders placed before noon CST, and exact job quotes are provided when you enter your address and project details on our site.

Use this simple formula: cubic yards = (square feet x depth in inches) / 324. For example, to raise 1,000 sq ft by 4 inches you need about 12.4 cubic yards; always add 5% to 10% for settlement and compaction and check with our materials calculator or sales team for a precise estimate.