Fill Dirt in Addison, TX

Delivered fill dirt in Addison typically ranges depending on supplier, distance, and moisture content. Expect roughly $10 to $30 per ton and about $12 to $36 per cubic yard as a general range (1 cubic yard is roughly 1.2 tons depending on moisture and compaction). Hello Gravel has a 3-ton minimum and delivery fees can change with access, truck turnaround, and next-day service requests.

For Addison's conditions, choose clean fill dirt with low organic content and a moderate clay-silt mix that compacts well but drains reasonably. Avoid topsoil or high-organic mixes for structural fills; contractors in the area prefer compactable, low-organic fill for grading and backfill, then cap with free-draining stone where needed.

Use this formula: cubic yards = (area in sq ft * depth in inches) / 324. Example: a typical 2-car driveway at 400 sq ft raised 4 inches needs about 4.9 cubic yards (roughly 6 tons). Leveling a 1,000 sq ft backyard 3 inches deep needs about 9.3 cubic yards (roughly 11 to 12 tons). Add 10-15% extra for compaction and waste.

Fill dirt is commonly used for bulk grading and creating positive slopes away from structures, but it is not an ideal wearing surface for driveways or pads. For driveway bases and parking pads in Addison's climate, contractors typically prefer a crushed stone or road base layer over compacted fill to improve drainage and reduce freeze-swell and rutting risk. Near foundations, use engineered compacted fill and follow local code or an engineer's guidance.

Install fill in lifts of 4 to 6 inches loose, then compact each lift with a plate compactor for small areas or a vibratory roller for larger areas. Aim for firm compaction; contractors often target 90-95% of standard Proctor for structural fills, but homeowners doing small repairs can usually get acceptable results with proper lift thickness and a good plate compactor. If the project is near foundations or driveways, consider professional compaction testing and heavier equipment.

Fill dirt is the least expensive option and is appropriate for bulk raising and grading, but it does not provide a stable, draining driving surface. Crusher run, road base, or limestone screenings are more costly per ton but compact into a stable, durable base that resists erosion and rutting in Addison's rain events and temperature swings. For long-term driveway performance, gravel or crushed stone base with a suitable wearing course outperforms plain fill dirt.

Hello Gravel works with local suppliers and uses dump trucks (typically tri-axle) with a 3-ton minimum order. Delivery restrictions in Addison commonly include truck access limits (turning radius, overhead wires, low gates), curb or homeowner responsibility for spreading, and scheduling lead times—standard delivery is 2+ business days, with next-day available if ordered before noon CST. Add delivery notes and photos at checkout if access looks tight.

An exposed fill dirt surface will settle, compact, and erode over time, especially after heavy rains common in the Dallas area, so expect periodic regrading and replenishment. To extend lifespan, seed and stabilize with vegetation, add a surface layer of gravel for traffic areas, and maintain positive drainage away from structures. For driveways and pads, a compacted stone base with a wearing course will dramatically reduce maintenance compared with bare fill dirt.

You can use compacted, low-organic fill dirt to raise grade or fill shallow depressions, but any work near foundations should follow local building codes and may require permits or inspections depending on scope. For critical fills next to structures, contractors typically use engineered fill and compaction testing and recommend consulting Addison/Dallas County building officials or a structural engineer before proceeding. Hello Gravel can deliver material, but structural use should be approved by the proper authorities or design professional.

A practical rule: 1 inch of fill over 1,000 sq ft equals about 3.1 cubic yards, which is roughly 3.7 tons depending on moisture and compaction. For quick estimates, use 3.1 cubic yards per 1,000 sq ft per inch, and convert cubic yards to tons using a local factor (commonly 1.1 to 1.3 tons per cubic yard for fill dirt). Always round up and add 10-15% for compaction and waste when ordering.