Fill Dirt in Stewart County, TN

In Stewart County, local suppliers for fill-dirt are typically small quarries, landscaping yards, road contractors and construction material suppliers serving rural Tennessee. Hello Gravel connects you with these local suppliers and contracted haulers based on your ZIP code, so enter your address or contact our team to get supplier options and local availability.

Hello Gravel’s minimum order is 3 tons, and standard delivery is scheduled for 2+ business days with next-day available for orders placed before noon CST. Delivery fees in rural areas around Stewart County commonly range from $0 to about $150 depending on distance, access and truck type; per-ton delivered prices for basic fill-dirt in the Tennessee region typically fall in the roughly $8 to $30 per ton range. For an exact price, check your ZIP code on our site or request a quote since local geology and haul distance drive price variation.

Fill-dirt is generally a fine, compactable material used to raise grade and backfill; it is not a finished surface. For driveways you should use compactable fill to build height, then cap with road base or crushed stone for durability. For building pads, use engineered, low-organic fill placed in controlled lifts and compacted to the engineer’s spec; ask for well-graded, non-organic fill. For septic systems, tank backfill can use clean, compactable fill, but leach fields typically require clean sand or gravel per health-department requirements—check local septic rules before ordering.

Stewart County’s wet winters and seasonal freeze/thaw increase the risk of settling and frost heave if fill is poorly drained or loosely placed. Choose well-draining, compactable fill, control surface and subsurface drainage, and place material in appropriate lifts with proper compaction to reduce long-term movement. Adding geotextile, drainage swales, or rock sub-base where needed can help extend performance in this climate.

Quantities vary by project and desired depth, but rough ranges are: 1-car driveway build-up typically 3 to 6 tons, 2-car driveway 6 to 12 tons, and a small building pad (20 ft x 20 ft raised about 6 inches) often needs about 20 to 40 tons. As a rule of thumb, 1 cubic yard of fill-dirt is about 1.0 to 1.3 tons depending on moisture and material; use Hello Gravel’s material calculator or send dimensions to our team for a precise estimate.

Stewart County may require engineered fill, compaction specifications, or compaction testing for foundation permits and some structural work; septic permits have separate material and installation rules through the county health office. Always check with Stewart County Building and Zoning and the Health Department before ordering fill-dirt for permitted work, and if your project needs engineered specs, plan to order fill that meets the engineer’s gradation and compaction requirements.

Fill-dirt is best for bulk raising and backfill but is not a durable wearing surface or planting medium. Crushed limestone or road base provides strength and drainage for driveways and access roads, while topsoil is required for vegetation and erosion control because it supports plant growth. For most Stewart County grading jobs you’ll use fill-dirt to build grade, road base or crushed stone for driving surfaces, and topsoil plus seed or mulch where you need erosion control and landscaping.

Yes. Rural Stewart County roads, bridges and seasonal spring weight restrictions can limit heavy loads or require lower truck weights and alternate routing; narrow driveways or low-clearance entrances can also affect truck access. These factors can increase hauling time or cost and sometimes require smaller trucks or split loads. When ordering, tell Hello Gravel about tight roads, bridge notices, or restricted access so we can coordinate the right truck and permits if needed.

Drivers may be able to provide tailgate spreading at their discretion, and you can request this service at checkout, but it is not guaranteed. The driver will assess site safety and accessibility on arrival and will only spread if it can be done safely; for controlled grading and compaction, plan to have a contractor or equipment on site.

Start by removing organic topsoil and debris from the placement area, place fill in uniform lifts (commonly 6 to 8 inches), control moisture, and compact each lift with appropriate equipment to the compaction target specified by your engineer (often 90% to 95% standard Proctor for structural work). For important structural or permitted work, hire a compaction testing service and follow any engineer or county requirements.