Fill Dirt in Collinsville, OK

In Collinsville and the West Oklahoma region, delivered fill-dirt commonly ranges from about $10 to $30 per ton depending on supplier, truck distance, and whether the material is screened or contains clay. Hello Gravel's minimum order is 3 tons, and delivery fees may be waived or added based on distance and site access. For an exact quote enter your zip code or call our team.

A 20 x 30 x 1-foot area equals 600 cubic feet, about 22.2 cubic yards. Typical fill-dirt weighs roughly 1.1 to 1.4 tons per cubic yard, so plan on about 24 to 31 tons depending on moisture and compaction. Order a little extra (5-10%) to allow for settlement and grading.

Hello Gravel connects you with local suppliers and haulers that serve Collinsville; specific supplier names and minimums vary by neighborhood. Through our platform most deliveries start at our 3-ton minimum, though some local farms or smaller haulers may set 5 to 10-yard minimums or charge a short-haul fee. Check availability and exact minimums by entering your zip code or contacting our team so we can match you with nearby options.

For raising grades and basic backfill, use clean fill-dirt with low organic content and minimal topsoil; it compacts reasonably well for non-structural fills. For driveway bases or where load-bearing is needed, a granular material (crushed stone, road base, or crusher run) is better than plain fill-dirt because it drains and compacts more reliably in Collinsville's clay-prone conditions. For foundation backfill, use engineered or select fill compacted in lifts per engineer specs to reduce settlement.

Collinsville experiences hot summers and occasional freeze-thaw cycles that can cause clay-rich fill-dirt to shrink, swell, or settle. Proper compaction, moisture conditioning, and surface drainage will greatly reduce movement; poorly compacted clay fill is most likely to cause uneven settlement or heaving. If your project is near structures or paved surfaces, consider engineered fill or granular materials to improve long-term stability.

Best practice is to place fill-dirt in 6- to 8-inch lifts and compact each lift to 90-95% of Standard Proctor density (or to the level specified by your engineer). Use a plate compactor or jumping jack for shallow lifts and tight areas, and a sheepsfoot or vibratory roller for larger fills. Monitor moisture content during compaction — too dry or too wet reduces achievable density — and test with a compaction test if the fill supports structures.

Fill-dirt is primarily for raising grade and backfill; it is not intended as a finished driveway surface. Crusher run and road base are engineered for driveway bases because they compact tightly and shed water, while topsoil is for planting and has high organic matter so it does not compact well. For a durable Collinsville driveway use road base or crusher run for the base layer and top with a wearing surface; reserve fill-dirt for leveling and non-bearing fills.

Small deliveries and minor grading around private residences typically do not require a permit, but larger projects that alter drainage, exceed certain cut-and-fill volumes, or disturb over an acre may trigger city or county permits and erosion control requirements. Check with the City of Collinsville planning department and Rogers County for thresholds and stormwater rules before you start. If in doubt, ask Hello Gravel or your contractor to help verify local permitting needs.

If fill-dirt is used as a surface, expect more frequent maintenance: periodic grading, adding material, and re-compaction every 1 to 3 years depending on use and weather. Annual or biannual spot grading by a local equipment operator can run a few hundred dollars; adding material costs depend on tonnage (typical fill-dirt pricing) and delivery. To reduce maintenance, use proper base materials and drainage during installation rather than relying on fill-dirt as the wearing surface.

Hello Gravel can match you with local haulers and contractors serving Collinsville, but if you reach out directly expect to see a wide range of rates. Typical equipment-plus-operator rates in the region can be roughly $80 to $200 per hour for skid steers or excavators, or $400 to $1,200 per day depending on machine size; laborers commonly range from $25 to $60 per hour. Always get multiple bids, confirm insurance and references, and ask for itemized quotes including hauling, spreading, compaction, and grading.