Stone in Riverside, IL

A typical dump-truck load of crushed stone for small cities like Riverside usually runs between about 10 and 14 tons, depending on truck type and material. Delivered price can vary with material, distance, and local availability, but expect a rough range of $300 to $1,000 for a full truckload in the Riverside area; specialty or washed stone can cost more. Hello Gravel requires a 3-ton minimum order and shows exact pricing after you enter your zip code, so get a quote for the best number.

The most budget-friendly options in the Midwest are generally crusher run (road base) for the base layer and 3/4u0022 crushed stone or 57 stone as a top wearing layer. Recycled or bank-run materials can also be cheaper in some local yards, but availability varies in Riverside because we source regionally. Use a cheaper base material and a more angular top stone for durability and compaction.

For Riverside's freeze-thaw winters and typical vehicle loads, you should not place stone directly on dirt for a driveway; a compacted base is important. We recommend at least 4 to 6 inches of compacted road base or crusher-run for driveways, with a 1 to 2 inch wearing layer on top; landscape fabric can help with weeds but is not a substitute for proper base and compaction. For light garden paths, 3 to 4 inches over compacted base may be acceptable.

Volume depends on your driveway width. For an example single-car 20 ft by 10 ft driveway: 2u0022 = ~1.24 yd3 (~1.7 tons), 3u0022 = ~1.85 yd3 (~2.6 tons), 4u0022 = ~2.47 yd3 (~3.5 tons. For a two-car 20 ft by 20 ft driveway: 2u0022 = ~2.47 yd3 (~3.5 tons), 3u0022 = ~3.70 yd3 (~5.2 tons), 4u0022 = ~4.94 yd3 (~6.9 tons). We used a common conversion of about 1.4 tons per cubic yard; order size should respect our 3-ton minimum and the need to round up for compaction and waste.

No, 2 inches of loose stone is generally too thin for a residential driveway in Riverside, especially with winter freeze-thaw cycles and vehicle traffic. For a long-lasting driveway we recommend a compacted base of 4 to 6 inches of road base and a 1 to 2 inch wearing layer of crushed stone. Two inches might be OK for a temporary solution or very light foot traffic only.

Cost depends on depth. For 1,000 sq ft: 2u0022 = ~6.17 yd3 (~8.6 tons), 3u0022 = ~9.26 yd3 (~13.0 tons), 4u0022 = ~12.35 yd3 (~17.3 tons). Using typical material prices of roughly $35 to $60 per ton in many Illinois markets, material cost could fall in ranges of about $300 to $1,050 plus delivery; Hello Gravel shows exact rates for your zip code and may offer free delivery in many areas.

Most driveway and base stones do not require washing; unwashed material with fines can actually help bind layers. Washed stone is useful when you need clean, decorative top material or for drainage applications. Many local suppliers in our network in and around Riverside can deliver washed stone on request, but washed options depend on regional availability—ask when you request a quote.

A 7x14 dump trailer will typically carry roughly 4 to 6 cubic yards of material depending on the sidewall height, while weight limits often cap the load to a few tons. That size trailer can be practical for very small jobs or tight-access sites, but weight restrictions and trailer GVWR limit how much stone you can haul compared with a tri-axle dump truck. Our delivery network usually uses dump trucks for reliability and higher capacity, but if you prefer a trailer drop-off check local supplier options and site access in Riverside first.

Stone is typically cheaper up front; a gravel driveway can cost roughly $1 to $3 per sq ft installed (material plus basic spread and compaction), while poured concrete driveways are commonly $6 to $12 per sq ft installed in the Midwest. Gravel usually has lower initial cost but requires periodic maintenance and topping, while concrete costs more to install but tends to need less frequent routine upkeep—consider your budget and long-term maintenance expectations given Riverside's freeze-thaw conditions.

Yes, there are several options such as resin-bound or resin-encapsulated gravels, polymer stabilizers, and gravel grid systems that lock stones together to reduce movement. These products can give a firmer, more finished surface than loose gravel but are not identical to poured concrete and availability varies locally. Ask our sales team for local suppliers and pricing—some stabilizers or pre-mixed stabilized aggregates can be ordered into Riverside through our network.

Hello Gravel requires a 3-ton minimum and connects you with local haulers who typically deliver by tri-axle dump truck; standard delivery is two or more business days, with next-day options for orders placed before noon CST. Mark your desired drop spot, check overhead clearances and driveway weight limits, and add any notes about color or spreading at checkout; drivers may offer tailgate spreading at their discretion but it is not guaranteed.