Fill Dirt in Conway, AR

Delivered prices for fill-dirt in Conway typically fall in a range rather than a single number because of local sourcing and haul distance. Expect roughly $10 to $25 per ton delivered for basic, clean fill-dirt, with lower rates closer to suppliers and higher rates for longer hauls or specialty screened material. Hello Gravel shows zip-specific quotes so check your delivery zip to see exact pricing and any current promotions.

Fill-dirt is usually fine-grained material that compacts well for raising grade but is not an ideal structural base on its own. For driveways and slabs in Conway, use engineered or well-graded compactable fill for lifts, then place a 4 to 6 inch crushed stone base (3/4u0022 minus or crusher-run) under the slab or pavement. If you must use fill-dirt to build grade, cap it with appropriate aggregate and compact in 6-inch lifts to avoid future settlement.

Central Arkansas soils around Conway often contain clay that expands when wet and shrinks when dry, and local storms can saturate shallow fills. That means uncompacted or poorly drained fill-dirt can settle, heave, or retain water. Proper moisture control, staged compaction, a granular cap or drainage layer, and positive site grading are important to reduce those risks.

A 20x40 driveway at 4 inches is about 800 sq ft and equals roughly 9.9 cubic yards of material. Using a common conversion of about 1.2 tons per cubic yard for compacted fill-dirt, that is roughly 12 tons in-place; allow 10-20% extra for compaction and waste and plan to order about 14 tons. Remember Hello Gravel minimums apply (3 tons) and truckload sizes may affect delivery splits.

If fill-dirt is properly placed, compacted in lifts, and capped with appropriate aggregate, it can perform well for many years as non-structural fill. As a structural base under driveways or slabs it is less reliable than engineered base materials and may show settlement within months to a few years if not prepared correctly. Inspect fills after heavy rains, fill low spots, regrade and reseed erosion-prone areas, and address drainage issues promptly to extend lifespan.

For slope stabilization in Conway's climate and clay soils, crushed stone or engineered structural fill combined with geotextile and erosion control is usually preferable because it improves drainage and resists erosion. Fill-dirt can be used to reshape or raise slopes but holds more water and is more susceptible to erosion unless protected by vegetation, mats, retaining walls, or a stone toe. Choose solutions based on slope steepness, drainage, and whether the slope is structural or cosmetic.

Hello Gravel's minimum order is 3 tons, and deliveries are typically made by tri-axle dump trucks. Tri-axle trucks commonly carry roughly 10 to 14 tons of fill-dirt depending on density (roughly 12 to 14 cubic yards loose), so larger orders may arrive by single truck while smaller orders could be consolidated. Haul fees vary by supplier distance—many local deliveries are free or low-fee, but long hauls or tight access can add charges; check your zip code for an exact quote.

Large grading, significant regrading, work in regulated floodplain areas, or projects that change drainage often trigger permits in Conway and Faulkner County. Permit thresholds and requirements vary by project size and location, so contact Conway City Planning or the building department before starting work and check FEMA/floodplain maps when relevant. Hello Gravel recommends confirming local permitting early to avoid rework or delays.

Recycled fill options (screened construction/demolition fines, screened RAP, or recycled fill) are often available near metro areas and can cost less than virgin screened fill. Savings depend on supply and quality—recycled materials can be 10% to 30% cheaper but may have greater variability and require testing for contaminants or unexpected contents. Ask your Hello Gravel supplier about local recycled options, request material descriptions, and consider a quick soil test for large projects.

Labor and equipment costs vary, but small residential machine work (site prep, placing and compacting fill) commonly ranges from about $10 to $30 per cubic yard, or $50 to $150 per hour for an operator with heavy equipment. For a sample 20x40 driveway fill (roughly 10 cubic yards in-place) expect contractor costs from a few hundred dollars up to $1,200 depending on access, complexity, and compaction requirements. Always get written bids that specify lift thickness, compaction specs, and testing if required.